Check whether you are using a normal 5V chargerCheck if the charging cable is broken

Instruction User Manual for Mimofpet GT1 Model Wireless Dog Fence/Dog Training Collar

Button Function

Turn On/Off

Remote:

Push to ON position to unlock, push to OFF position to lock.If the display does not light up, charge it.

Collar:

Short press the power button for 1 second to turn it on.(Goes to sleep mode after 6 minutes of inactivity)

Beep&Ultrasonic Command

Short press beep button on the remote, and the receiver will emit a beep.

Long press will make a ultrasonic sound.

Vibration Intensity Adjustment

Press () to adjust the vibration levels from 0 to 9.Level 0 means no vibration, and level 9 is the strongest vibration.
Short press () for one vibration, long press for continuous vibration of 8 seconds.

Shock Intensity Adjustment

()Shock increase button

()Shock decrease button

Level 0 means no shock, and level 9 is the strongest shock.
2.Short press() for one shock, long press for continuous shock of 8 seconds.

Shock Intensity Test

Screw the contact points onto the collar and tighten it by using the test light hole.
Place the bottom of the test light onto the contact points. Make sure the conductive wire inside the test light touches the top of the contact points.
Press the shock button on the remote and observe the brightness of the test light.

Level 1: Faintlight, Level 30: High light.

Electronic Fence Mode(Electric shock or no shock can be selected)

Press () to enter the fence mode with no shock (), and press again to exit the fence mode.

()Electronic fence level increase button

()Electronic fence level decrease button

Tip: When you are not using the electronic fence function, it is recommended to exit the electronic fence mode to save power.

Long Press () to enter the fence mode with no shock (), and press again to exit the fence mode.

()Electronic fence level increase button

()Electronic fence level decrease button

Tip: When you are not using the electronic fence function, it is recommended to exit the electronic fence mode to save power.

14 Levels Of Fence Range

The electronic fence ranges from the lowest level 1 to the highest level 14, with a distance of 25FT(8m) to 3500FT(1050m).

The values on this graph are for reference only

Level 1 is about 25Ft(8M)
Level 5 is about 200Ft(60M)
Level 10 is about 450Ft(135M)
Level 13 is about 1000Ft(300M)
Level 14 is about 3500Ft(1050M)

Please test the fence levels to find a level that is appropriate for the environment that you are using the fence in. Please note that the signal will be affected by your environment. The distance of the same level is usually different when you use it at home and open area outdoor.

For indoor or yard use, the fence radius will be reduced by wall and other RF signal interference. The distance levels provided are based on measurements taken in open areas and are intended for reference purposes only.

When The Dog Crosses The Boundary: Fence Mode:No Shock

For the safety of dogs, the automatic warning does NOT HAVE SHOCK.If you need a fence mode with electric shock, please long press the fence button to switch to fence with shock mode.

When The Dog Crosses The Boundary: Fence Mode:With Shock

When you set the vibration level to 0 before entering fence mode, then there is no vibration when dog crosses the boundary.

When you set the shock level to 0 before entering fence mode, then there is no shock when dog crosses the boundary

The vibration and shock levels can be set individually for each dog.

Important Notes Before Entering Fence Mode

Please note that the vibration and electric shock warning levels for dogs that cross the boundary are based on the levels set before entering the fence mode.

After setting the vibration and shock level, you need to press the vibration/shock button to save the setting, then enter fence mode.

Step1:

Take off the collar from your dog’s neck (To prevent accidental shock to your dog when setting the levels)

Step3:

Press the setting button(wireless fence button) on the left side to enter fence in fence mode

Step2:

Vibration level adjustment + press vibration
button to confirm the level that will be used in fence mode
Shock level adjustment + press shock button to confirm the level that will be used in fence mode

If multiple dogs are using the fence at the same time, the level of each dog’s out-of-boundary warning will be based on the vibration and electric shock levels set for each dog before entering the fence mode.

The vibration and shock levels cannot be adjusted in Fence Mode.

Screen Dispaly In Fence Mode

When controlling multiple dogs:The shock level, vibration level and receiver’s battery status are not displayed

Factors Affecting Fence Signals

Keep away from metal appliances when using the wireless fence, do not put the remote control on such appliances

Do not hang the remote control on the indoor wall or place it on the ground, otherwise the fence signal will be be weakened.

When the dog lies on the ground and covers the collar, causing signal interference, it is recommended to wear the collar on the side of the dog’s neck or on the back

Pairing (Already paired at the factory)

Press and hold () for 3 seconds, the icon () flashes to enter pairing.
Short press the () on the remote control to select the channel that you want to pair the collar.
When the collar is turned off, press and hold () for 3 seconds until the LED light flashes red and green.
Press the () button to confirm pairing. It will beep to indicate pairing is successful.

Cancel Pairing

Press and hold () for 3 seconds,the icon () flashes to enter pairing.
Short press the switch channel to select the collar to unpair.
Press the () button to delete the pairing.
Press the () button to exit pairing.

Pairing With Multiple Collars

Repeat the above operations, you can continue to pair other collars.

After the four channels are paired, press () to select channels from 1 to 4 to control single collar seperatedly or control all the collars together at the same time.

Control Multiple Collars In Training Mode

1.When controlling multiple dogs, the vibration and shock levels can be set individually for each dog.

2.When controlling multiple collars, the screen does not display the shock level and vibration level

Wearing Precautions

Wearing the collar for too long or too tightly can cause abrasion on the dog's skin, leading to redness or bedsores
Make sure the dog does not wear the collar for more than 12 hours a day.
Please readjust the position of the collar on the pet's neck every 1 to 2 hours. check the tightness of the collar regularly to prevent excessive pressure.
Do not tie the leash to the receiver as this will cause excessive pressure on the collar.
Please clean the contact area between the pet's neck and the receiver with a damp cloth every week.
Check the contact area every day for signs of rash or pain.
If you notice a rash or pain on your dog, stop using the collar until the skin heals. If this condition persists for more than 48 hours, see a doctor immediately.

Training Tips

Choose suitable contact points for your dog.
If the hair is too thick, separate it by hand so that the contact points touches the skin, making sure both electrodes touch the skin at the same time.
The tightness of the collar tied to the dog’s neck is suitable for inserting a finger.
Shock training is not recommended for dogs under 6 months of age, aged, in poor health, pregnant, aggressive, or aggressive towards humans.
In order to make your pet less shocked by electric shock, it is recommended to use sound training first, then vibration, and finally use electric shock training. Then you can train your pet step by step.
The level of electric shock should start from level 1.

Wearing the Collar

Frequently Asked Questions

If you have any questions, please feel free to contact our customer service team.

What Is The Center Point Of The Fence?

Remote control is the center point

Will Training Functions Work Normally When The Fence Is On?

The training function can be used in the fence mode, you can manually train your pet through the remote. Note:The training level needs to be set before entering the fence mode. Please refer to page 6 for Preset Operations.

The Boundary Zone Seems To Fluctuate

This is normal for the electromagnetic field of the Wireless System. The field may be affected by surrounding radio frequency or other signals.

Fence False Alarm

The remote control or receiver is close to metal items, causing serious signal interference
When the dog lies on the ground and covers the collar, causing signal interference, it is recommended to wear the collar on the side of the dog’s neck or on the back
Check if the collar is turned on
Affected by other radio interference in the surrounding area
The recommended height for placing the remote control is about1 meter

When Out Of Range, Do The Warnings Stop Immediately After Returning To Range Or Is There A Delay?

There is usually a delay of about 3-5 seconds

Shock/Vibration Does Not Work

Check whether the shock or vibration level setting is 0 or not
The dog’s hair is too thick, push aside the dog’s hair and put the contact points in contact with the dog’s skin
The collar is too loose, it is recommended to leave a gap of one finger when wearing it

Can Multiple Collars Be Controlled Simultaneously?

Yes, our system can control a single collar seperatedly or all paired collars together at the same time

Will Singals Between Collars Affect Each Other When Controlling Multiple Collar?

No, they will not affect each other

Can Not Be Turned On

Try to turn on the device after fully charging it

Unable To Charge

Check whether you are using a normal 5V charger
Check if the charging cable is broken

Accessories Damaged

Please take a video or photo and send it to our after-sales team to solve it for you

Important Safety Information

Disassembly of the collar is strictly prohibited under any circumstances, as it may destroy the waterproof function and thus void the product warranty.
If you want to test the electric shock function of the product, please use the delivered neon bulb for testing, do not test with your hands to avoid accidental injury.
Note that interference from the environment may cause the product to not work properly, such as high-voltage facilities, communication towers, thunderstorms and strong winds, large buildings, strong electromagnetic interference, etc.
1. When pressing buttons such as vibration or electric shock, and there is no response, you should first check: 1.1 Check if the remote control and collar are turned on. 1.2 Check whether the battery power of the remote control and collar is sufficient. 1.3 Check if the charger is 5V, or try another charging cable. 1.4 If the battery has not been used for a long time and the battery voltage is lower than the charging start voltage, it should be charged for a different period of time. 1.5 Verify that the collar is providing stimulation to your pet by placing a test light on the collar.
2. If the shock is weak, or has no effect on pets at all, you should check first. 2.1 Make sure that the contact points of the collar are snug against the pet's skin. 2.2 Try increasing the shock level.
3. If the remote control and collar do not respond or cannot receive signals, you should check first: 3.1 Check whether the remote control and the collar are successfully matched first.
3.2 If it cannot be paired, the collar and remote control should be fully charged first. The collar must be in the off state, and then long press the power button for 3 seconds to enter the red and green light flashing state before pairing (valid time is 30 seconds). 3.3 Check if the button of the remote control is pressed. 3.4 Check whether there is a electromagnetic field interference, strong signal etc.You can cancel the pairing first, and then re-pairing can automatically select a new channel to avoid interference.
4.The collar automatically emits sound, vibration, or electric shock signal, you can check first: check whether the remote control buttons are stuck.

Operating Environment And Maintenance

Do not operate the device in temperatures of 104°F and above.
The remote control is not waterproof, please do not use this product in rain
Do not use this product in places with strong electromagnetic interference, which will seriously damage the performance of the product.
Avoid dropping the device on a hard surface or applying excessive pressure to it.
Do not use it in a corrosive environment, so as not to cause discoloration, deformation and other damage to the appearance of the product.
When not using this product, wipe the surface of the product clean, turn off the power, put it in the box, and put it in a cool and dry place.
The collar cannot be immersed in water for a long time.
If the remote control falls into the water, please take it out quickly and turn off the power, and then it can be used normally after drying the water.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and collar.

—Connect the equipment into an outlet on a circuit different from that to which the collar is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance, such modifications could void the user’s authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Specification

Specification	Parameters
Model	GT1
Packing size (1 collar)	6.7 * 4.49 * 1.73 inches
Package weight (1 collar)	0.63 Pounds
Packing size (2 collars)	6.89 * 6.69 * 1.77 inches
Package weight (2 collars)	0.85 Pounds
Remote control weight (single)	0.15 Pounds
Collar weight (single)	0.18 Pounds
Adjustable of collar	Maximum circumference 23.6 inches
Suitable for dogs weight	10-130 Pounds
Collar IP rating	IPX7
Remote control waterproof rating	Not waterproof
Collar battery capacity	350mAh
Remote control battery capacity	800mAh
Collar charging time	2 hours
Remote control charging time	2 hours
Collar standby time	185 days
Remote control standby time	185 days
Collar charging interface	Type-C connection, use ordinary charger head, not fast charger head
Signal receiving method	Two-way reception
Training mode	Beep/Ultrasonic/Vibration/Shock
Vibration level	0-9
Shock level	0-9
Power consumption of the collar/remote control	9μΑ
Collar standby power consumption	60μΑ
Remote control standby power consumption	48μΑ

In the Box(1 Collar)

1. Remote control 1PCS

2. Collar unit 1PCS

3. Collar strap 1PCS

4. USB cable 1PCS

5. Contact points 2PCS

6. Test light 1PCS

7. Lanyard 1PCS

8. User manual 1PCS

In the Box(2 Collars)